What Types of Cables Do Telecommunications Contractors Install? | Los Angeles Telecom Techs

What Types of Cables Do Telecommunications Contractors Install?

Walk into any modern office, warehouse or school and you’ll find miles of cable hidden in the ceilings, walls and floors. Most people never think about it until something stops working. But the type of cable installed, and how it’s installed, determines how fast your network runs, how well your Wi-Fi performs and how long your infrastructure lasts. At Los Angeles Telecom Techs, we install every kind of low-voltage cable used in commercial buildings across Los Angeles, and this guide breaks down each type, what it’s used for and how contractors decide which one belongs where.

Quick Reference: Common Cable Types

Here’s a summary of the cables you’ll find in most commercial telecommunications projects:

CableTypical usePerformance
Cat6Desk drops, phones, printers, standard cameras250 MHz; 1 Gbps to 100 m
Cat6AWi-Fi access points, PoE cameras, 10G links500 MHz; 10 Gbps to 100 m
Multimode fiber (OM3/OM4)Backbone inside a building10 Gbps to 300–400 m
Single-mode fiber (OS2)Long risers and campus links10 Gbps to 10 km and beyond
Speaker cablePaging and AV speakersSized to run length and power
Shielded audio cableMicrophones and audioRoom to building scale
Access control composite cableCard readers, locks, door sensorsPanel to door runs
Coaxial cableLegacy cameras, TV and some antenna systemsVaries by type

Good to know: most businesses rely mainly on Cat6, Cat6A and fiber. The specialty cables come into play for paging, AV, security and access control.

Copper Twisted-Pair Cable

Twisted-pair copper is the workhorse of business networks. Each cable contains four pairs of copper wires twisted together, which reduces interference between them. It carries Ethernet data and, through Power over Ethernet (PoE), can also power phones, cameras and access points. Copper links are limited to 100 meters per channel, including patch cords.

Cat5e

Cat5e was the standard for many years and supports gigabit Ethernet. It’s still found in older buildings, but it’s rarely installed in new commercial work because Cat6 and Cat6A offer more headroom for a small difference in cost.

Cat6

Cat6 is rated to 250 MHz and is the most common cable for everyday desk connections. It supports gigabit Ethernet to 100 meters, multi-gig speeds of 2.5 and 5 Gbps in most installations, and 10 Gbps over shorter runs of roughly 55 meters. It’s a solid, cost-effective choice for computers, VoIP phones and printers.

Cat6A

Cat6A, or Augmented Category 6, is rated to 500 MHz and supports 10 Gbps over the full 100 meters. It has better resistance to crosstalk from neighboring cables and handles high-power PoE more effectively. Cat6A has become the standard for Wi-Fi 6E and Wi-Fi 7 access points, PTZ cameras, switch uplinks and any location expected to need more speed in the future. The trade-off is size: Cat6A is noticeably thicker, so pathways and racks must be planned for it.

Shielded vs. unshielded

Most commercial cabling is unshielded twisted pair (U/UTP). In areas with heavy electrical noise, such as near motors, drives and industrial equipment, contractors install shielded cable (F/UTP) with shielded jacks, bonded to the building’s grounding system.

Cat8

Cat8 supports 25 and 40 Gbps over very short distances, about 30 meters. It’s designed for connections between switches and servers in data centers and is rarely used for general office cabling.

Fiber Optic Cable

Fiber optic cable carries data as pulses of light through strands of glass. It supports far greater distances and bandwidth than copper and is immune to electrical interference, which makes it ideal for backbone connections.

Multimode fiber (OM3, OM4, OM5)

Multimode fiber has a larger core and is used for shorter runs inside a building, such as connecting the main telecom room to telecom rooms on each floor. OM3 supports 10 Gbps to about 300 meters and OM4 to about 400 meters. OM5 is designed to carry multiple wavelengths for certain high-speed applications.

Single-mode fiber (OS2)

Single-mode fiber has a much smaller core and carries signals over very long distances, 10 kilometers and beyond at 10 Gbps. It’s used for long risers in high-rise buildings, links between buildings on a campus and connections to carrier networks.

Indoor, outdoor and armored fiber

Fiber comes in versions for every environment: indoor cable for risers and plenum ceilings, outdoor cable for conduit between buildings, indoor/outdoor cable that transitions between the two, and armored cable for areas where crushing or rodents are a risk.

MPO trunk cables

MPO cables carry 12 or 24 fibers in a single connector. They’re pre-terminated at the factory and used in data rooms where high density and fast installation matter.

Cable Jacket Ratings

A cable’s jacket determines where it can legally be installed. Fire codes require specific ratings for different spaces, and inspectors check them. Here are the ratings telecommunications contractors work with most:

RatingWhere it’s usedWhy it matters
Plenum (CMP / OFNP)Return-air spaces above drop ceilings and under raised floorsHighest fire rating for indoor cable
Riser (CMR / OFNR)Vertical shafts and runs between floorsLimits fire spreading floor to floor
General purpose (CM / OFN)Non-plenum, non-riser indoor spacesLowest indoor rating
Outdoor / direct burialConduit between buildings, exterior walls, yardsResists moisture and UV
Indoor/outdoorRuns that pass from outside into a buildingOne cable for both environments
ArmoredAreas with crush or rodent riskMetal or dielectric armor for protection

Using the wrong jacket, such as general-purpose cable in a plenum ceiling, can fail inspection and create a real fire risk. Experienced contractors match the jacket to every space along the route.

So far, we’ve covered the copper and fiber that carry most business data. That’s the heart of network cabling, but a building’s full communications system includes much more. If you’re unclear where one ends and the other begins, our article on the difference between telecommunications and network cabling explains how the two relate.

Specialty Low-Voltage Cable

Beyond copper and fiber for networking, telecommunications contractors install a range of specialty cables for voice, audio, video and security systems.

Speaker cable

Speaker cable connects overhead paging speakers, warehouse horns and conference room speakers to amplifiers. Its thickness is chosen based on run length and the power the speakers need, so sound stays clear at the far end of the line.

Shielded audio cable

Microphones and other low-level audio signals use shielded cable to keep out hum and noise. Many modern conference systems now send audio over Cat6 instead, using network audio.

Access control composite cable

Composite cable bundles the conductors a controlled door needs into a single jacket: wiring for the card reader, lock power, door position switch and request-to-exit device. It keeps door installations neat and easy to service.

Security and alarm cable

Multi-conductor low-voltage cable is used for door contacts, sensors, electric strikes and other security devices that don’t run over the network.

Coaxial cable

Coax was the standard for analog security cameras and cable television. It’s still found in older buildings and in some antenna and video distribution systems, though most new cameras now use Cat6 with PoE.

AV cabling: HDMI, HDBaseT and USB

Conference rooms use HDMI and USB for short connections, and HDBaseT over Cat6 or Cat6A to send video, audio and control to displays up to 100 meters away.

Multi-pair voice cable

Multi-pair copper cable still carries analog lines in some buildings, such as for fax machines, alarm panels and elevator emergency phones.

42U network rack in a West LA office IDF with 48-port Cat6A patch panels, horizontal wire managers and an OM4 fiber enclosure
IDF buildout: 42U rack on 19-inch EIA-310 rails, 48-port Cat6A patch panels with 1U horizontal managers, and an LC fiber enclosure fed by OM4 riser backbone.

Connectors and Termination Hardware

Cable is only half the installation. Every run ends in hardware that must match the cable’s rating:

  • RJ45 keystone jacks and wall plates at outlets for copper cable
  • Patch panels in the telecom room where copper runs are terminated
  • Field-terminated plugs for direct connections to cameras and access points
  • LC, SC and MPO connectors for fiber
  • Fiber enclosures and splice trays that protect fiber terminations

Mixing categories, such as Cat6 cable on Cat5e jacks, drops the whole link to the lower rating. Professional contractors use matched components from a single system so links can be certified and warranted.

How Contractors Choose the Right Cable

Choosing cable is a design decision, not a guess. Contractors weigh several factors:

  1. Distance. Copper is limited to 100 meters. Longer runs need fiber or an additional telecom room.
  2. Speed. Gigabit devices are well served by Cat6. Multi-gig access points and 10 Gbps links call for Cat6A or fiber.
  3. Power. High-power PoE devices perform better on Cat6A, which handles heat in bundles more effectively.
  4. Environment. Plenum ceilings, risers, outdoors and industrial areas each require specific jackets or shielding.
  5. Code requirements. Jacket ratings, firestopping and pathway rules must be met to pass inspection.
  6. Future plans. Installing higher-category cable now often costs less than replacing it in a few years.

Cable Choices in Los Angeles Buildings

Local conditions shape cable choices too. Many Los Angeles office towers have return-air plenum ceilings that require plenum-rated cable throughout. High-rise risers need riser-rated copper and fiber, with every floor penetration firestopped. Outdoor cameras and access points face strong sun and, near the coast, salt air, so outdoor-rated cable and sealed connections matter. Campuses and warehouses often need underground conduit with outdoor or armored fiber, and older buildings may require creative routing where ceilings can’t be opened.

Frequently Asked Questions

What is the most common cable installed in offices today?

Cat6 for standard desk connections, with Cat6A increasingly used for Wi-Fi access points, PoE cameras and any location that needs multi-gigabit speeds or high-power PoE.

Is Cat5e still installed?

Rarely in new commercial work. Cat5e still supports gigabit and even 2.5 Gbps in many cases, but most businesses choose Cat6 or Cat6A for headroom and longer useful life.

When is fiber better than copper?

Fiber is the better choice for runs longer than 100 meters, links between floors and buildings, and backbone connections that need very high bandwidth or immunity to electrical interference.

What does plenum-rated mean?

Plenum-rated cable has a jacket designed to limit flame spread and smoke, and it’s required in air-handling spaces such as many drop-ceiling return-air plenums.

Do security cameras and Wi-Fi use special cable?

They use the same Cat6 or Cat6A as network devices, powered through PoE. Outdoor cameras need outdoor-rated cable, and very distant cameras may use fiber.

Final Thoughts

Telecommunications contractors install a wide range of cables: Cat6 and Cat6A copper for network devices, multimode and single-mode fiber for backbones and long runs, and specialty cable for paging, audio, security, access control and AV. Each one is chosen for its distance, speed, power, environment and code requirements, then installed with matched hardware and certified.

If your building already has cabling, the question becomes whether it can keep up with what you need today. Our article on whether a telecommunications contractor can upgrade an existing network explains how existing cabling is evaluated and when it can be reused, improved or replaced.

Planning a cabling project in Los Angeles? Call (562) 245-4723 for a site walk and itemized quote.

Request a quote
Scroll to Top