Can a Telecommunications Contractor Upgrade an Existing Network? | Los Angeles Telecom Techs

Can a Telecommunications Contractor Upgrade an Existing Network?

Your business has grown, your devices have changed and your network isn’t keeping up. Wi-Fi slows down in meetings, phones drop calls and the telecom room has become a tangle nobody wants to touch. The good news is that you rarely need to start over. At Los Angeles Telecom Techs, we upgrade existing networks for businesses across Los Angeles every week, and this guide explains how a telecommunications contractor evaluates what you have, decides what to keep and upgrades your network without bringing your business to a halt.

The Short Answer

Yes. A telecommunications contractor can upgrade an existing network by testing the cabling already in place, keeping what still performs, replacing what doesn’t, and adding the capacity your business needs now. Upgrades can be as small as replacing a few access point runs or as large as rebuilding telecom rooms and installing new fiber backbone.

Key point: a good upgrade starts with testing, not guessing. Certification results show exactly which cables can stay and which need to go, so you only pay for what’s actually needed.

Signs Your Network Needs an Upgrade

Network problems often look like equipment issues, but many of them trace back to cabling and infrastructure. Watch for these signs:

  • Wi-Fi is slow or drops in busy areas, even with new access points
  • Connections run at 100 Mbps instead of gigabit
  • Phones, cameras or access points reboot randomly
  • New Wi-Fi 6E or Wi-Fi 7 access points can’t reach their full speed
  • Your telecom room is crowded, unlabeled or overheating
  • You’re adding staff, devices or space
  • Your cabling is Cat5 or early Cat5e, installed 15 or more years ago
  • Nobody can say which port goes where

If several of these sound familiar, an assessment can show whether the cause is cabling, capacity or equipment, and what it will take to fix it.

What a Network Upgrade Can Include

Network upgrades come in many forms. Most projects combine two or three of the following:

Cabling upgrades

Older Cat5 and Cat5e cabling is replaced with Cat6 for desks and Cat6A for access points, cameras and uplinks. Often only the most demanding runs need upgrading, while other runs that still test well stay in place.

Wi-Fi infrastructure upgrades

New Wi-Fi 6E and Wi-Fi 7 access points need multi-gigabit uplinks and more PoE power. Upgrades typically include new Cat6A runs to each access point, relocating access points to better positions and adding coverage where it’s missing.

Telecom room cleanup and rebuild

Crowded racks are reorganized with proper cable managers, right-length patch cords and clear labels. Racks are anchored and braced, grounding is added, and space is created for new equipment.

Fiber backbone upgrades

Older or undersized fiber between floors and buildings is replaced or supplemented with new single-mode or OM4 fiber, adding bandwidth and spare strands for growth.

PoE and power capacity

As more devices draw power over Ethernet, cabling and switch power budgets need to keep up. Upgrades confirm every powered device gets the PoE it needs.

New drops and expanded coverage

Growing teams need more data drops, new conference rooms and coverage in areas that were never wired, such as warehouse extensions or converted storage rooms.

Voice, security and AV additions

Upgrades are often the right time to add VoIP phones, security cameras, access control or video conferencing, all using the improved cabling foundation.

What Shapes the Scope of an Upgrade

Every upgrade is different, and several factors determine how large the project becomes:

  • How much existing cabling passes testing. The more that can be reused, the smaller the project.
  • The devices you’re adding. Multi-gig access points, PTZ cameras and high-power PoE devices may require Cat6A.
  • Building conditions. Hard-lid ceilings, concrete walls and crowded risers take more time to work through.
  • Telecom room condition. A room that needs new racks, bracing and grounding adds to the scope.
  • Distance. Areas beyond 100 meters from a telecom room need fiber or a new IDF.
  • Scheduling requirements. After-hours and weekend work keeps your business running but must be planned into the timeline.

An itemized assessment turns these factors into a clear scope, so you can prioritize the upgrades that matter most and phase the rest over time.

How a Contractor Evaluates Your Existing Network

Before recommending anything, a contractor needs to know what’s already in your walls and ceilings. A typical evaluation includes a site walk, a review of your telecom rooms, tracing and testing existing cabling, and a comparison against what your business needs now and in the next few years.

Testing is where the real answers come from. Here’s what common findings usually mean:

FindingWhat it meansTypical action
Links pass Cat6 or Cat6A certificationThe cabling performs to its ratingKeep and re-label
Links pass but are Cat5eFine for basic devices, limited for future speedsKeep for desks, upgrade key runs
Links fail certificationDamage, bad terminations or excess lengthRe-terminate or replace
Runs over 100 mBeyond copper’s distance limitAdd an IDF or fiber
Abandoned or unknown cableDead runs crowding ceilingsRemove accessible abandoned cable
Crowded or unbraced racksHard to manage and a seismic riskRebuild and brace the telecom room

Identifying the cable in place is the first step in interpreting these results. If you’d like to understand the differences between Cat5e, Cat6, Cat6A, fiber and specialty cable before your assessment, our guide to the types of cables telecommunications contractors install explains each one and where it’s used.

Reuse, Upgrade or Replace?

Every cable and component in your network falls into one of four categories after testing:

DecisionWhen it appliesWhat happens
ReuseCable is the right category, tests well and is in the right locationsLowest cost; re-label and document
UpgradeCable is usable but terminations, racks or labeling are poorRe-terminate, re-dress and certify
ReplaceCable fails testing, is too old or too slow for new devicesInstall new Cat6, Cat6A or fiber
AddCoverage or capacity is missingNew drops, access points or fiber links

This approach keeps upgrade costs in check. Instead of replacing everything, you invest where it makes the biggest difference and keep what still works.

42U network rack in a West LA office IDF with 48-port Cat6A patch panels, horizontal wire managers and an OM4 fiber enclosure
IDF buildout: 42U rack on 19-inch EIA-310 rails, 48-port Cat6A patch panels with 1U horizontal managers, and an LC fiber enclosure fed by OM4 riser backbone.

The Upgrade Process, Step by Step

  1. Assessment. The contractor walks the site, inspects telecom rooms and tests existing cabling.
  2. Findings and plan. You receive a report showing what passed, what failed and what’s recommended, with an itemized scope.
  3. Phasing. The work is divided into phases that fit around your business hours and priorities.
  4. New infrastructure. New cabling, fiber and telecom room upgrades are installed alongside the existing network.
  5. Cutover. Devices are moved to the new cabling during planned windows, usually after hours.
  6. Cleanup. Abandoned cable is removed and telecom rooms are re-dressed.
  7. Certification and documentation. Every new and reused link is tested, labeled and recorded on updated drawings.

Upgrading Without Disrupting Your Business

One of the biggest concerns with any upgrade is downtime. Experienced contractors plan around it:

  • Parallel installation. New cabling is pulled while the old network keeps running.
  • After-hours cutovers. Switching devices to new cabling happens at night or on weekends.
  • Phased work. Upgrades move area by area, so only a small part of the office is affected at a time.
  • Clear communication. Your team knows what’s happening, when and which areas are affected.

Upgrading Networks in Los Angeles Buildings

Los Angeles buildings add a few considerations to any upgrade. Many older offices have ceilings full of abandoned cable left by previous tenants, and accessible abandoned cable is generally required to be removed under the electrical code. Return-air plenum ceilings, common in commercial towers, require plenum-rated replacement cable. Telecom room upgrades are a good time to add seismic anchoring and bracing that older racks often lack. In multi-tenant buildings, landlord rules may limit work hours, riser access and cable types, so upgrades need to be scheduled and documented to building standards.

Planning Ahead So the Next Upgrade Is Easier

A well-run upgrade also sets you up for the future. Ask your contractor to leave spare ports in patch panels, extra strands in new fiber, empty rack space for new equipment and service loops at each outlet. Make sure every link is labeled and every result is saved in a certification report. With accurate documentation in hand, the next upgrade starts from known facts instead of guesswork, and moves, adds and changes take hours instead of days.

Who Does What: Contractor vs. IT Team

Network upgrades work best when responsibilities are clear:

  • The telecommunications contractor handles the physical infrastructure: cabling, fiber, telecom rooms, access point mounting, testing and documentation.
  • Your IT team or managed service provider handles network equipment and configuration: switches, firewalls, Wi-Fi controllers, VLANs and security settings.

The two work together on timing, port assignments and cutovers so that new cabling and new equipment come online smoothly.

Frequently Asked Questions

Can existing cabling be reused during an upgrade?

Often, yes. Cabling that tests well, is the right category and lands in the right places can usually be kept. Testing is the only reliable way to know, which is why it should come first.

Do I need to replace all my cabling to get faster Wi-Fi?

Not necessarily. Many upgrades focus on the runs that matter most, such as replacing access point cabling with Cat6A, while desk drops that already perform well stay in place.

Will my business have to shut down during a network upgrade?

Rarely. Most upgrades are phased, with new cabling installed alongside the old and cutovers scheduled after hours or on weekends.

How long does a network upgrade take?

Small upgrades can take a day or two. Larger projects that include new cabling, telecom room work and fiber may take one to several weeks, often completed in phases.

Does an upgrade include new switches and firewalls?

The contractor handles the physical infrastructure. New switches, firewalls and network configuration are typically handled by your IT team or managed service provider, working alongside the contractor.

Final Thoughts

Upgrading an existing network doesn’t have to mean starting from scratch. A telecommunications contractor can test what you have, keep what still performs, replace what doesn’t and add the capacity your business needs, all while keeping disruption to a minimum. The result is a faster, more reliable and better-documented network built on the investment you’ve already made.

The real payoff of an upgrade shows up in everyday work: clearer calls, smoother video meetings and fewer interruptions. To see why the cabling behind your systems makes such a difference, read our article on how proper cabling can improve business communications.

Planning a cabling project in Los Angeles? Call (562) 245-4723 for a site walk and itemized quote.

Request a quote
Scroll to Top