Telecommunications Contractor in Culver City CA – #1 C7 Licensed Contractor

Telecommunications Contractor in Culver City CA – Commercial and Industrial

Commercial telecommunications cabling contractor providing network cabling, structured cabling, fiber optic cabling, Wi-Fi installation, low-voltage communications wiring, voice, data and AV infrastructure.

Planning a move, buildout or network refresh? Call (562) 245-4723 for a site walk and itemized quote.

Request a quote

Telecommunications Cabling Services

Our technicians install, label and test every cable themselves, following the ANSI/TIA standards used for commercial cabling installations across the United States. Most projects combine two or three of these services in a single mobilization.

Data Telecom Cabling Installation

Cat6 • Cat6A • Ethernet • Data Cabling • PoE • Patch Panels

New drops, moves, adds and changes for copper Ethernet, terminated to keystone jacks and patch panels in your data telecom closets and tested for PoE devices.

Structured Cabling Installation

MDF • IDF • Racks • Patch Panels • Backbone Cabling

Telecom room design and buildout, from riser backbone between floors to rack mounting, dressing and wire management.

Fiber Optic Cabling

Single-Mode • Multimode • Fusion Splicing • LC/SC • OTDR

Indoor, riser-rated and outside plant fiber, including runs in external conduit between buildings, fusion spliced, terminated and certified with OTDR traces.

Commercial Wi-Fi Installation

Wireless Access Points • PoE • Wi-Fi Infrastructure

Site surveys, access point mounting, Cat6A uplinks, PoE switching and wireless coverage validation.

Voice & Communications

VoIP • Paging • Intercom • Communications Cabling

Wiring and device setup for VoIP handsets, overhead paging zones and door intercom stations, connected to your business phone system.

Security System Cabling

IP Cameras • PoE Cameras • Access Control

Home-run PoE cabling for IP cameras, card readers, door contacts and electrified hardware.

AV & Conference Room Cabling

Displays • Video Conferencing • AV Cabling

Display, camera and table-box cabling for huddle rooms, boardrooms and training spaces wired for video conferencing.

Telecommunications Infrastructure We Install in Culver City

  • Cat6
  • Cat6A
  • Fiber Optic
  • Ethernet
  • PoE
  • Patch Panels
  • Network Racks
  • MDF
  • IDF
  • Wireless Access Points
  • VoIP
  • Paging
  • Intercom
  • IP Cameras
  • Access Control
  • AV

Most offices we wire now run on Cat6A horizontal cabling to support 10GBASE-T uplinks and high-wattage PoE for Wi-Fi 6E and Wi-Fi 7 access points. We route each cable through J-hooks or tray, hold bend radius and separation from electrical lines, and terminate on angled or flat patch panels with front and rear cable management.

In the telecom room, we’re mounting two- and four-post racks with seismic bracing anchored to slab, a real consideration in Culver City’s older concrete and converted industrial buildings. The communications backbone between the MDF and each IDF is typically OS2 single-mode or OM4 multimode fiber, fusion-spliced to pigtails in rack-mount enclosures and connected with LC duplex patch cords.

MediaBandwidth / speedMaximum distanceTypical applicationTest method
Cat6 U/UTP250 MHz; 1 Gbps (10 Gbps to 55 m)100 m channelDesk drops, VoIP handsets, printersCopper certification to TIA-568.2-D
Cat6A500 MHz; 10 Gbps100 m channel / 90 m permanent linkWi-Fi 6E/7 access points, PoE cameras, 10G uplinksCopper certification to TIA-568.2-D
PoE (IEEE 802.3af/at/bt)15.4 W / 30 W / up to 90 W at the switch100 mCameras, access points, intercoms, door readersLink and load verification
OS2 single-mode fiber1310 / 1550 nm; 10G–100G+10 km+ at 10 GbpsCampus and building-to-building backboneTier 1 loss + Tier 2 OTDR
OM4 multimode fiber850 nm; 10G to 400 m, 100G-SR4 to 150 m400 m at 10 GbpsMDF-to-IDF riser backboneTier 1 loss + Tier 2 OTDR
Fusion splice / connector≤0.3 dB per splice, ≤0.75 dB per mated pair (TIA-568.3-D)—Pigtails, LC/SC terminationsSplice loss estimate + OTDR event table
42U network rack in a Culver City office IDF with 48-port Cat6A patch panels, horizontal wire managers and an OM4 fiber enclosure
IDF buildout: 42U rack on 19-inch EIA-310 rails, 48-port Cat6A patch panels with 1U horizontal managers, and an LC fiber enclosure fed by OM4 riser backbone.

Telecommunications Cabling for Commercial Facilities in Culver City

  • Offices
  • Warehouses
  • Schools
  • Medical Facilities
  • Retail
  • Industrial Facilities
  • Commercial Buildings

We bring a full range of cabling services to occupied buildings and new telecom construction alike, and we take on small jobs, like adding a handful of drops, as readily as full-floor buildouts. Noisy work is scheduled after hours so your business keeps operating.

Hayden Tract creative offices

Converted industrial buildings with exposed ceilings: Cat6A in tray to every workstation and access point, a new IDF, and dense Wi-Fi 6E for open floors.

Downtown Culver City offices

Mixed-use buildings near Culver and Washington Boulevards needing multi-gig PoE uplinks and conference rooms wired for video calls.

Studio-area post-production suites

Edit bays and screening rooms near the studio lots connected with 10G copper and fiber so large media files reach shared storage without bottlenecks.

Jefferson Boulevard warehouses

Light industrial and distribution spaces cabled for scanner Wi-Fi above racking, PoE cameras on dock doors, and fiber to remote IDFs.

Problems We Solve for IT Managers who have Customers in Culver City

Unlabeled, undocumented cabling

We re-terminate and label every port to TIA-606 and hand over as-built drawings, so moves and troubleshooting start from a spreadsheet instead of a ceiling tile.

Wi-Fi that drops in busy areas

We survey, relocate and add access points, then wire them with Cat6A so Wi-Fi 6E and Wi-Fi 7 radios get the multi-gigabit uplinks and PoE power they need.

Overloaded telecom rooms

We rebuild IDFs with proper racks, wire managers and right-length patch cords, cutting heat buildup and making failed links easy to trace.

Buildings beyond copper’s reach

We extend single-mode or multimode fiber to warehouse mezzanines, detached buildings and far-end IDFs past the 100 m copper limit.

Our Telecommunications Cabling Installation Process for Our Culver City Customers

  1. Site walk and scope

    We walk the space, review floor plans, locate telecom rooms and pathways, and confirm drop counts and device locations.

  2. Design and itemized quote

    You get a written scope listing media type, drop counts, rack elevations and fiber backbone design, with a schedule built around your operations. If your MDF is backed by a standby generator, we coordinate with your general contractor and electrician, since permitting and compliance with California Air Resources Board rules sit with them.

  3. Pathways and rough-in

    Installers set J-hooks, sleeves, ladder rack and firestopping, then pull copper and fiber to each outlet and telecom room. Penetrations through structural slabs are core-drilled only with engineer approval.

  4. Termination and mounting

    Copper is terminated to jacks and patch panels, fiber is fusion spliced or connectorized, and racks, access points and devices are mounted.

  5. Testing and certification

    Every copper link and fiber strand is tested, and results are saved against the port labels.

  6. Labeling and handoff

    You receive labeled outlets and panels, as-built drawings and the full certification report.

Telecommunications Cabling Testing & Certification

Many cable contractors stop at a continuity check, which only proves a link is connected. Certification proves it will carry the speed it was installed for. We certify copper permanent links for insertion loss, NEXT, return loss and length, and test fiber with Tier 1 light-source power-meter readings plus Tier 2 OTDR traces that show every splice and connector along the run.

Reports are delivered as PDF files tied to your patch panel labels, which makes manufacturer warranty registration and future troubleshooting simple.

Technician certifying a Cat6A permanent link at a patch panel and fusion splicing OS2 single-mode fiber in a rack-mount enclosure in Culver City
Cat6A permanent links are certified to 500 MHz over a maximum of 90 m. Fiber splices are verified on OTDR against the TIA-568.3-D limit of 0.3 dB per splice.

Telecommunications Contractor Service Area in Culver City and Southern California

Our office on West Olympic Boulevard puts our crews minutes from Culver City, with multi-site work across Southern California. Neighborhoods we cover in Culver City include Downtown Culver City, the Hayden Tract, the Washington Boulevard Arts District, the Jefferson Boulevard corridor, Fox Hills, Blair Hills, Culver West and Sunkist Park.

Request a Telecommunications Cabling Quote

Send us the address, approximate square footage and the number of data drops, access points or cameras you need. Floor plans help. We’ll schedule a site walk and follow up with an itemized scope.

We hold a California C-7 state license issued by the Contractors State License Board in Sacramento (CSLB #[NUMBER]).

Los Angeles Telecom Techs
11340 W Olympic Blvd, Los Angeles, CA 90064
Tel: (562) 245-4723
Email: [email protected]

Get your wiring installed, tested and certified on schedule.

Request a quote

Scroll to Top